Audio Products

Tonearm

 

1H

Figure 2. Carbon fiber. Reed 1H has a cardanic bearing system: vertical axis has thrust rotation bearings and horizontal axis is based on thrust pivot bearings (same concept as in Reed 3P). Such bearing construction eliminates wobbling of a bearing, which has a great impact on the quality of the sound. Among other features, Reed 1H tonearm has azimuth adjustment, replaceable headshell a...[more]

Tonearm

2G

Reed 2G with the laser option   Laser-enabled Reed 2G version continues tradition of Reed 3Q and helps audio enthusiasts to set up their systems using latest technology. Calibrated laser add-on, used in this tonearm version, allows user to adjust VTA and azimuth quickly and precisely.   ...[more]

Tonearm

3P

Another 3Ps innovation is its bearing system. Although tonearm bearing system can be considered as gimbal, it acts like unipivot one. However, major difference from unipivot system is that instead of a single pivot three pivots and both vertical and horizontal axis’ magnetic stabilizers are used. Such bearing system is as rigid as gimbal, but its friction coefficient is as low as in unipi...[more]

Tonearm

5A

P1, O1, P3 – Thales’ semicircle, P1-A1-P3, P1-A2-P3, P1-A3-P3 angles are 90⁰ each, A1,1B1 = A2,1B2= A3,1B3 segments represent tonearm length, 1B – vertical axis of the tonearm, 1P2 – center of the circle, which is drawn through three points -1B1,1B2,1B3,- axis of rotation of the back link component 2P2 – center of the circle, which is drawn th...[more]

Tonearm

5T

    P1, O1, P3 – Thales’ semicircle,     Angles P1-A1-P3, P1-A2-P3, P1-A3-P3 are 90 degrees each,     Segments A1B1 = A2B2= A3B3 represent length of a tonearm,     B – Tonearm vertical axis,     P2 represents a center of circle, drawn through three points – B1,B2 and B3 (tonearm ro...[more]

Tonearm

AF10 Tonearm

Tonearm

Cobra

Our choice was to use a jewel pivot as found in the finest of aircraft instruments, which offer the lowest friction possible via mechanical means. Stabilisation is via outrigger pivot, which allows for precise azimuth adjustment. VTA is adjustable on the fly using a 40TPI microscope fine pitch thread vertical adjustment mechanism. Clamping is by a triangulated locking system which avoids the co...[more]

Tonearm

TA01

  The geometry and size of the Thiele TA01 is dimensioned in a way, that it can be mounted on every turntable which is designed for 9“ or 10“ conventional tonearms. The supplied massive alumium alignment protractor allows for an absolute precise positioning of the Thiele TA01 tonearm on your turntable. @font-face {font-family:"Cambria Math"; panose-1:2 4 5 3 5 4 6...[more]

Tonearm

TDTW-01Ti

Titanium Tonearm Wand TDTW-01Ti Armwand to upgrade Graham Phantom Elite tonearm (10 inch) A one-piece high rigid tonearm wand machined from solid pure titanium with special hardening treatment Stella Inc. is pleased to offer an option to upgrade the acknowledged Graham’s PHANTOM Elite tonearm. This new titanium arm wand has been developed based on our accumulated experiences of engine...[more]

Tonearm

Viper
Award Winning Product

Viper Tonearm: Minimal Mass, Maximum Rigidity To many enthusiasts and experts, the Viper tonearm supplied with Obsidian might look impossibly massive. Once they lift it, they will immediately realize that not only is the Viper much lighter than it looks, it’s also much more rigid than other tonearms. Why such a large tonearm? Because every percentage of increase in the width or ...[more]

Tonearm